Search

Surplus and Used Slitter Rewinders for Sale, Duplex, Centerwind, Two Drum for Paper Film or Foil.

140” Jagenberg Vari-Dur Type 45-15 Slitter Rewinder 140" Web Width 60” Rewind Diameter 500

126810
140” Jagenberg Vari-Dur Type 45-15 Slitter Rewinder 140" Web Width 60” Rewind Diameter 5000 FPM Used Finishing / Converting Winder. Jagenberg surface rewinder features: Shaftless 72” diameter Jagenberg Unwind; Slitting section with ten (10) shear slitters; rider roll; water cooled brakes; Hydraulic Edge Guide; Reliance DC Drives; Unloading Table. Also includes some tooling spare parts manuals electrical & mechanical drawings and chucks for 3” 5” 6” 12” core sizes. The winder was in good operational condition when shutdown.

65” Trim Width Dusenbery Model 10000 Slitter Rewind. Level 3. Duplex Slitter Rewind

126180
65” Trim Width Dusenbery Model 10000 Slitter Rewind. Level 3. Duplex Slitter Rewind Arrangement. Attached Unwind 42” Diameter. Erhardt and Leimer Web Guide. Shear Cut Slitting. 24” Max Rewind Diameter. Center Wind with Lay-on Rolls. Cantilevered Rewind Shafts.

60" Width Double Turret Unwind 60" Width 70" Diameter Rolls Includes Drive and Controls.

126280
60" Width Double Turret Unwind 60" Width 70" Diameter Rolls Includes Drive and Controls.

60" Black Clawson Turret Rewind 60" Wide by 36" Diameter Rolls.

125910
60" Black Clawson Turret Rewind 60" Wide by 36" Diameter Rolls. Includes load censors for tension control and Accuguide unit. Set up for 3" Shafts. Has 7.5 HP DC motors for center wind and 4.9 HP 230/460 Volt Turret Motor.

60” Black Clawson Turret Rewinder 60” Width x 36” Diameter Rolls. 3” Rewind Shafts.

125911
60” Black Clawson Turret Rewinder 60” Width x 36” Diameter Rolls. 3” Rewind Shafts. Inlcudes load cells for tension control and an Accuguide unit. Winder drive is 7.5 HP DC motor. Turret Motor is 4.9 HP 230/460 V Motor.

13.5” Arpeco Tracker Salvage Slitter Rewinder. Was in operating condition when pulled out

125978
13.5” Arpeco Tracker Salvage Slitter Rewinder. Was in operating condition when pulled out of service for newer equipment. Web width 12”. May be seen with mechanical and electrical turnover.

4” Dusenbury Table Salvage Rewinder Model 750AB ½ HP. Was in operating condition when pull

125979
4” Dusenbury Table Salvage Rewinder Model 750AB ½ HP. Was in operating condition when pulled out of service for newer equipment. Table Winder can be seen under power.

65” Width x 72” Diameter; ECH Will Dual Floor Pickup Unwinds with Marquip Tail-grabber Splicer

126765
65” Width x 72” Diameter; ECH Will Dual Floor Pickup Unwinds with Marquip Tail-grabber Splicers. Set of Two (2); Total of Four (4) unwinds with (2) Splicers. Includes Overhead Frame Input System.

Powell Shaftless Floor Pick-Up Unwind Stand 96" Wide 72" Max Diameter 10000 Pound Capacity

126156
Powell Shaftless Floor Pick-Up Unwind Stand 96" Wide 72" Max Diameter 10000 Pound Capacity 12" Chucks Dual Air Brakes.

75" ECH Will unwinds Six (6) Available.

126159
75" ECH Will unwinds Six (6) Available. Each with Double E 3"/5" combo chucks Dual 15" air brakes 75" wide by 60" diameter rolls Shaftless floor pick-up roll out stands 230/460 volt Above the Floor Design Requires flat steel tracks. Quantity (6).

70” Width x 58” Diameter Unwinds with regenerative braking Quantity (2).

126128
70” Width x 58” Diameter Unwinds with regenerative braking Quantity (2). Include edge guide and tension control.